Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Logic Low

GENERAL

Product Name

32 Channels High-Range DIO

Part Numbersnumbers

OP5369

Board Typetype

Digital input/output conditioning

Form Factorfactor

Mezzanine Type B

Dimensions

6.60 cm x 12.50 cm (2.6” x 4.92”)

Hot-Plug support

No

Characteristic

Number of Channelschannels

32 IO in 4 Banks configurable as inputs or outputs  Bank1 : D0-7    Bank2 : D8-15   Bank3 : D16-23     Bank4 : D24-31

Vuser 1 VUser1 for Bank 1 and 2      Vuser 2 VUser2 for Bank 3 and 4

INPUT DIRECTION

Input Impedanceimpedance

> 100 K OhmkOhm

Reverse voltage protection

Signal diodeDiode

Maximum  voltage protection

+/- 50 Volts

Detection threshold

4 programmable Schmitt Trigger  Level trigger level step 0.1176V 118V from 0.470v 470V to 29.4 Threshold 4V threshold high and Threshold Low threshold low for each bank

Recommended levels threshold

The default thresholds are LOW level = 1.5V, the HIGH Level = 3.5V.

To improve noise immunity, a LOW - level Threshold threshold of 1/3 Vuser, VUser and a HIGH - level Threshold threshold of 2/3 Vuser, VUser are recommended.

Voltage Rangerange

0 to 30 Vdc

Delay Low-to-High

10 ns (implementation-dependent)                                                         

Delay High-to-Low

15 ns (implementation-dependent)                                                        

OUTPUT DIRECTION

Output Protectionprotection

50 mA resettable fuse

Output impedance2 to 15 ohmOhm

Protection thresholds

Maximum Vuser VUser + 0.5V

Minimum  -0.5V

Output voltage range

4.5 to 24Vdc 25Vdc Max (default internal 4.5 volts)

Logic high levels (typical) 

Vuser <= 25v , noload:  Vuser No load:  VUser -0.2V   50mA : Vuser  

50mA :     VUser -0.9V (in OP5650 system)  

Vuser  >  25v , noload:  Vuser -3.5V   50mA: Vuser -4.7V (in OP5650 system)  

OP5XXX system)    

Logic low levels (typical) Vuser  5V to 30V 0.1V ( in OP5650 system)  

No load:  0.1V 

50 mA:     0.9V (in OP5XXX system)

Output configuration

Push-pull 

Delay Low-to-high High (  hardware typical * typical value, implementation-dependent)

< 100ns @25c for  25V@25°C for  25V 

< 90ns @25c for @25°C for 5 V                                        

Delay High-to-Low (  hardware typical * typical value, implementation-dependent)

< 100ns @25c for  @25°C for  25V

< 90ns @5c for @25°C for 5 V                                          

Rise / Fall time ( x to Y)

< 40ns,    50ns  < 50ns                                   

Minimum Pulse pulse detection (resolution)

90 ns      5V130ns ns   5V

130 ns  30V

Output Frequencyfrequency

 DC DC to 8 Mbit (14MHz (see table below)

Environmental


Background Color
color#D3D3D3


 

The OP5369 is designed for indoor use only.

( * ) implementation-dependent 


Module operating temperature

0 °C to 40 °C

Storage temperature

-40 °C to 85 °C

Operating humidity

10% to 90% non-condensing

Storage humidity

5% to 95% non-condensing

Pollution Degreedegree

2

Maximum altitude

2,000 m

Power requirement15W

Maximum PWM Output Frequency for Given Number of Repetitive Signals

in

OP5650
or
/OP5x07/OP5705/OP4610
in
OP4510
Vuser / Channel

<=

30V

25V

<=12V<=5V<=
30V
25V<=12V<=5V
1 1
Mb/s
MHz2
Mb/s5 Mb/s16Kb/s
MHz4 MHz16 kHz **2
Mb/s5 Mb/s
MHz4 MHz
5
  1Mb/s
 1 MHz2
Mb/s5 Mb/s16Kb/s
MHz4 MHz16 kHz **1
Mb/s
MHz4
Mb/s
MHz
15
500Kb/s
0.3 MHz **2
Mb/s5 Mb/s16Kb/s**500 Kb/s2 Mb/s32500Kb/s1 Mb/s4 Mb/s16Kb/s**500 Kb/s1 Mb/s**500 Kb/s  si T amb < 25C*1 Mb/s si T amb < 25C

...

MHz4 MHz16 kHz **0.5 MHz2 MHz
320.3 MHz **1 MHz4 MHz16 kHz **0.5 MHz1 MHz
**0.5 MHz if T amb <= 25°C