Pour la documentation en FRANÇAIS, utilisez l’outil de traduction de votre navigateur Chrome, Edge ou Safari. Voir un exemple.


The activated modes of ePHASORSIM’s parallel feature are determined using the following license keys:

EPHASOR_PARALLELIZE_GENUNITSePHASORSIM parallelizes the computation of generator units (GenUnits)
EPHASOR_PARTITION_POWERSYSTEMePHASORSIM also parallelizes the nodal equations

Note: If neither of the above license keys is enabled, no parallelization occurs.

The parallelization is controlled using:

  • the EPHASOR_THREADS environment variable
  • Two parameters in the Simulation settings tab of the Simulink mask: Number of partitions and Optimize number of threads (Windows only)

On Windows, the recommended way to use parallelism in ePHASORSIM is to enable the Optimize number of threads algorithm option in the Solver mask.

It is not recommended to use the EPHASOR_THREADS variable so that the algorithm can find the best setting. Defining EPHASOR_THREADS on Windows restricts the range of number of thread-pool sizes the algorithm will test.

Note: If MATLAB is started in standalone mode (i.e not through RT-LAB), the EPHASOR_THREADS variable potentially defined in the RT-LAB project will not be active, unless this variable is defined explicitly as an environment variable of the machine.

On Linux, by default, ePHASORSIM uses the 3rd core (core No. 2 with zero indexing) unless the EPHASOR_THREADS environment variable is defined. If the performance is not optimal (e.g. if there are overruns) parallelism can be controlled by defining EPHASOR_THREADS to change the number of threads, or to control core assignment to avoid conflicts with other RT-LAB features such as ARTEMiS or some drivers.

Refer to Parallel simulation rules for a more detailed overview of how to set up parallelism in ePHASORSIM.

Parallel Simulation Rules

The following abbreviations are used throughout this guide:

NPNumber of partitions parameter, set in the mask.
ONTOptimize number of threads (Windows only) algorithm, set in the mask.
NCNumber of available physical cores of simulator.

  • on Windows: NC = number of exiting CPU cores.
  • on Linux: NC = min(number of existing CPU cores, value of EPHASOR_NUM_CORES in the license)
maxNTHmaximum number of threads that can be used for parallelization.

  • if EPHASOR_THREADS is defined: maxNTH = number of cores specified in EPHASOR_THREADS, with an upper limit of NC - 2
  • if EPHASOR_THREADS is not defined: maxNTH = 1
NTHactual number of threads used by ePHASORSIM to parallelize GenUnits (and nodal equations if NP > 1)

  • if ONT is disabled: NTH = min(maxNTH, NC - 2)
  • if ONT is enabled (Windows only): During the first few steps of the simulation, the optimization algorithm finds the optimal value for NTH within the following range: 1<= NTH <= min(maxNTH, NC - 2)

The first and second table below summarizes calculations of NTH and also parallelization modes for Windows and Linux targets respectively.

Summary of Parallelization Modes for a Windows Target









NTH is:

Calculated optimally in this range:

[1,min(maxNTH, NC-2)]

min(maxNTH, NC-2)

Parallelization Mode is:

GenUnits only

Entire Network

GenUnits only

Entire Network

Summary of Parallelization Modes for a Linux Target




NTH is:

min(maxNTH, NC-2)

Parallelization Mode is:

GenUnits only

Entire Network


The syntax for EPHASOR_THREADS is EPHASOR_THREADS=<core_list>, where the <core_list> grammar is given in the following table.

Syntax Table for the EPHASOR_THREADS Variable

<core_list> :=

<elem> | <elem>,<core_list>

<elem> :=

<core_id> | <range>

<range> :=


<core_id> :=


Its meaning is the same on Windows and Linux, with the exception that:

  • On Linux, it is used to define which cores specifically will be used in the simulation (sets the affinity).
  • On Windows, it is used only to deduce the number of cores that the simulation will run on, but cannot assign specific cores.

For example, EPHASOR_THREADS = 3 and EPHASOR_THREADS = 5 mean that we want the simulation to run on only one core. On Linux, it also defines which core should be used (core 3 in the first case, core 5 in the second case).

The following examples are all valid values:

EPHASOR_THREADS=2,3,5in this case, we want to use 3 cores (on Linux, cores 2, 3, and 5)
EPHASOR_THREADS=3-6this is equivalent to EPHASOR_THREADS=3,4,5,6 meaning we want to use 4 cores (on Linux, cores 3, 4, 5, and 6)
EPHASOR_THREADS=2,4-6this is equivalent to EPHASOR_THREADS=2,4,5,6
If EPHASOR_THREADS is not defined, the default value is 2 - (NC - 2)


EPHASOR_THREADS may be defined as a user environment variable.

Users can define the variable in an RT-LAB’s project configuration, as in the following figure.


When using MATLAB directly, set EPHASOR_THREADS as a system environment variable prior to launching MATLAB. This can be done in System Properties, as in the figure below.

Defining EPHASOR_THREADS in the Windows environment variables for a MATLAB simulation

Notes on Linux Targets and EPHASOR_THREADS

  • Care must be taken to avoid conflicts in core assignment. For example, if in the model there is a driver that uses core 4, this core should not be used in the value of EPHASOR_THREADS. Otherwise, unknown behavior could occur.
  • The core IDs are 0 indexed.
  • Cores 0 and 1 are reserved for RT-LAB. Only cores indexed 2 and greater are recommended for use with the EPHASOR_THREADS variable.
  • Please refer to, Migration Notes, to see changes regarding to EPHASOR_THREADS in different versions.
  • No labels